Important: For your safety, set up the system before plugging it into a power source.ġ. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.
The socket-outlet shall be installed near the equipment and shall be easily accessible. The apparatus shall be disconnected from the mains by placing the power/standby switch in the standby position and unplugging the power cord of the speakers from the AC mains receptacle. 
Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Refer all servicing to qualified service personnel. Unplug this apparatus during lightning storms or when unused for long periods of time. Only use attachments/accessories specified by the manufacturer. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Operate the appartus only from the low level audio line output jack of the computer or of an audio device. If the provided plug does notįit into your outlet, consult an electrician for replacement of the obsolete outlet. The wide blade is provided for your safety. A polarized plug has two blades with one wider than the other. Do not defeat the safety purpose of the polarized plug. Logitech x 530 manual pdf install#
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Place apparatus in a stable location so it will not fall causing product damage or bodily harm. No naked (open) flame sources, such as lighted candles, should be placed on or near the apparatus. Ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table clothes, curtains, etc. Maintain a minimum distance of at least 6 inches around apparatus for sufficient ventilation. Do not push objects into apparatus vents or slots because fire or electric shock hazards could result. Install in accordance with manufacturer’s instructions. Do not block any ventilation openings. Any faults here might lead to the wire to the touch the ground wire or box. Strip the wire perfect such that no insulating material goes underneath the slot, and no bare wire is left. In case there's a airport terminal slot, you have to be extra careful. Also ensure that all the wire that's covered around the screw is stripped. That will way, the mess tightens the connection as it moves in. When wrapping a wire around the terminal screw, do it in a clockwise direction. Terminal connections experience a lot of stress, and weak joints easily loosen. These are generally some of the most typical connections, particularly if you're working together with receptacles and changes. Terminal contacts will be the end factors of wires, where a connection with another circuit occurs. Also, ensure you've obtained a tester to test the volt quality of the cables before and after working on them. Typically the ordinary pliers would give you a loose connection that may cause trouble in future. Opt for linesman pliers rather than the ordinary slip-joint huge pliers when intending to twist wires. Knives may weaken the line by notching the copper inside. For occasion, avoid knives as opposed to strippers when stripping your wires. Having the right tools at hand is another important aspect of power work. This keeps both you and your family safe. So if you accidentally touch a live line, the RCD would detect the unusual flow of the existing and immediately switch off the circuit. RCDs are devices that are utilized to monitor the flow of current through a particular circuit, and they cut off the current whenever it runs through an unintended path. 
It is located on outlet outlets or blend boxes to prevent electrocution in the case of a DO IT YOURSELF blunder. Have an RCDĪn RCD (residual current device) is one of the main things to have in your circuits. You will be in a lot better position to safeguard yourself and work better. To make you better at wiring, here are some reliable tips and techniques you need to master. However, you are able to work on small electrical wiring in your house provided you follow safety precautions. Electricity is very dangerous and can certainly lead to electrocution, so you need to call an emergency electrician for sensitive cabling cases. Best tricks and techniques in home electrical wiringįor DO-IT-YOURSELF electricians, there's a lot of cluttered up information of what you need to or ought not to do.
0 kommentar(er)
